Tuner2Patch TAP

TAPs für die SRP- und CRP-Serie
Benutzeravatar
FireBird
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Beiträge: 28745
Registriert: Fr 9. Dez 2005, 09:59
Receivertyp: SRP-2401CI+ TFIR
vu+ Duo 4k
Wohnort: Wien

Re: Tuner2Patch TAP

#21

Beitrag von FireBird » Mo 17. Sep 2018, 14:00

Achso. T2P schaltet 10 Sekunden vor dem Start eines Timers um. Da es zu dem Zeitpunkt auch den Sender auf T1 "irgendwo hin" schaltet, sollte sich auf jeden Fall auf dem Fernseher etwas tun.

2401
Topfazubi
Topfazubi
Beiträge: 49
Registriert: Do 6. Sep 2012, 16:58
Receivertyp: CRP-2401CI+
Receiverfirmware: 1.06.00

Re: Tuner2Patch TAP

#22

Beitrag von 2401 » Mo 17. Sep 2018, 14:07

FireBird hat geschrieben:
Mo 17. Sep 2018, 09:50
Es gibt einen australischen User, der sein Tuner1-Problem mit der Heißluftpistole gefixt hat, daher die Annahme. Klar, wir wissen noch zu wenig über das Problem.
Did that Australian user fixed the problem by heating the CPU with heat gun (or some other component), and if CPU do you know if he removed the heat sink during operation (because it seems to be glued so there is always need to reattach it with suitable tape or glue if removed once)?
I've been considering to try heating CPU myself but since this patch, I've been waiting because that is always uncharted territory and things can go terribly wrong and usually reflowing with heat gun trick is not permanent - I used to do that for my PS3 and it would work for few months until procedure needed to repeat. I guess eventually soldering get in to state where that won't help. But anyway, I'm interested. Is there discussion somewhere, could you post a link?

wohliks hat geschrieben:
Mo 17. Sep 2018, 10:55
Die Meldung lautet ja auch nicht "Kein Signal" wie bei Empfangsproblemen, sondern "Kein Programm oder verschlüsselt"...
Same here with my CRP.

Benutzeravatar
FireBird
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Beiträge: 28745
Registriert: Fr 9. Dez 2005, 09:59
Receivertyp: SRP-2401CI+ TFIR
vu+ Duo 4k
Wohnort: Wien

Re: Tuner2Patch TAP

#23

Beitrag von FireBird » Mo 17. Sep 2018, 14:31

This was the mentioned post. His Toppy still seems to work today.

Benutzeravatar
Ricki
ToppiHolic
ToppiHolic
Beiträge: 5626
Registriert: Fr 9. Dez 2005, 23:06
Receivertyp: 2xSky Q
MagentaTV MR601
2xUltimo4K DVB-S2x FBC
Receiverfirmware: Alle aktuell
Wohnort: Wetter/Hessen
Kontaktdaten:

Re: Tuner2Patch TAP

#24

Beitrag von Ricki » Mo 17. Sep 2018, 14:31

Mein Problem ist das der Topf ARD und ZDF die auf P1 und 2 stehen beim Scan mit 0% abschließt! Also müßte ich einen weg finden, dass der Topf 3 Minuten vor dem Scan an geht und an bleibt ohne den Scan zu verschieben. Oder ich hole einen anderen Topf aus der Schublade. :X
cu
Ricki


SmartEPGvu+ & SmartFilervu+ Wiki

SAT Anlage - Kathrein: CAS 75 mit UAS 584 LNB & EXR 1512 (Multischalter 5 auf 12), Astra 19.2°E

VU+ ULTIMO 4K DVB-S2x FBC+Samsung SSD870 QVO , 2 TB
VU+ ULTIMO 4K DVB-S2x FBC+Kingston SSDSUV400S, 480 GB
Skin: Vu_HD_1080P mit angepassten Skinparts - VTi 15.0.02
Plugins: smartEPGvu+ , Multi QuickButton, OpenWebif, AutocutVfd, GithubPluginUpdater, InfoBarTunerState, VTi Panel

Panasonic TX-55GZW1509; Sony UBP-X700, Apple TV 4K, Fire TV 4K, Harmony Elite, Denon AVR-X2300W, Synology 716+ (6TB)

Benutzeravatar
wohliks
Elko-Papst
Elko-Papst
Beiträge: 4452
Registriert: Fr 9. Dez 2005, 15:36
Receivertyp: 2x VU+Duo4KSE; (no HD+)
Wohnort: Nordhessen

Re: Tuner2Patch TAP

#25

Beitrag von wohliks » Mo 17. Sep 2018, 14:49

Ricki hat geschrieben:
Mo 17. Sep 2018, 14:31
Mein Problem ist das der Topf ARD und ZDF die auf P1 und 2 stehen beim Scan mit 0% abschließt! Also müßte ich einen weg finden, dass der Topf 3 Minuten vor dem Scan an geht und an bleibt ohne den Scan zu verschieben. Oder ich hole einen anderen Topf aus der Schublade. :X
Hab ich zwar hier schon mal geschrieben, aber vielleicht hast Du's überlesen: Probiere mal das TAP "StartConfig" aus, vielleicht hilft das bei Deinem speziellen Problem.

Das TAP stellt auf dem Toppi beim Ausschalten vor dem Herunterfahren einen in der .ini definierten Kanal und Tuner (z.B. Prog. 1 auf Tuner 2) ein, so dass er beim nächsten Start definiert mit diesem Programm auf diesem Tuner "hochkommt". Der EPG-Scan erfolgt dann auf diesem Tuner und läuft - bei mir jedenfalls - problemlos durch. Tuner2Patch agiert ja im Vorfeld einer Aufnahme und kann daher beim SE-Scan nicht helfen - das schrieb FireBird auch schon mal so.
Zuletzt geändert von wohliks am Mo 17. Sep 2018, 14:52, insgesamt 1-mal geändert.
Gruß Bernhard

2x VU+ Duo 4k SE - kein HD+ - SmartEPG
60 cm Astra (FTA only), hama LYPSI Quad LNB, Schwaiger SEW 4358 5/8-Multiswitch
FB: Logitech Harmony 650 & 600

Benutzeravatar
FireBird
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Beiträge: 28745
Registriert: Fr 9. Dez 2005, 09:59
Receivertyp: SRP-2401CI+ TFIR
vu+ Duo 4k
Wohnort: Wien

Re: Tuner2Patch TAP

#26

Beitrag von FireBird » Mo 17. Sep 2018, 14:51

Du hast in der letzte Zeit nicht viel Glück mit Deinen Töpfen. :rolleyes: Ich kann ja noch das eine oder andere Feature in T2P einbauen, aber hast Du das StartConfig einmal ausprobiert?

2401
Topfazubi
Topfazubi
Beiträge: 49
Registriert: Do 6. Sep 2012, 16:58
Receivertyp: CRP-2401CI+
Receiverfirmware: 1.06.00

Re: Tuner2Patch TAP

#27

Beitrag von 2401 » Mo 17. Sep 2018, 14:52

FireBird hat geschrieben:
Mo 17. Sep 2018, 14:31
This was the mentioned post. His Toppy still seems to work today.
Thanks. I browsed thru thread quickly and looked to me like he needed to redo reflow very soon but after second time it has been working, he was talking about using some fluid too. Anyway definitely looks what my hunch said to me after I tried to fix my PSU with no help on tuner problem. As far as I know this Toppy is also so new that it is using lead free soldering. Those are notorious because soldering are not "flexible" and repeated heat and cold cycles will crack them open at some point, or something like that. Just what is said in the link I posted about reballing.

Obviously that person did process with heat sink on but I did not quite get how he wrapped heat sink in foil but what part he did heat exactly, and if I understood correctly he used a blow torch (flame?) and 2 minutes, that's pretty long. Anyway if I remember correctly what I did to my PS3 was that I wrapped mainboard surface with tin foil and cut opening for CPU and then heated it gradually from top and bottom of the mainboard and increased heat towards end and then mostly heated top of the CPU. This is faint memory and from years ago. Again this procedure is very ghetto way to try fix things and it can easily go wrong, so do not try it unless you are prepared to possibility that it can kill the unit. Also if you heat it with heat gun parts around CPU will get hot too and it is always possible that some parts get knocked off from their position or even short some part, so it should not be flipped or tilted during that. Best way would be to find company that has right equipment and knowledge to do this and it would be pretty permanently fixed. This heat gun trick will not last forever.

2401
Topfazubi
Topfazubi
Beiträge: 49
Registriert: Do 6. Sep 2012, 16:58
Receivertyp: CRP-2401CI+
Receiverfirmware: 1.06.00

Re: Tuner2Patch TAP

#28

Beitrag von 2401 » Mo 17. Sep 2018, 15:03

wohliks hat geschrieben:
Mo 17. Sep 2018, 14:49
Das TAP stellt auf dem Toppi beim Ausschalten vor dem Herunterfahren einen in der .ini definierten Kanal und Tuner (z.B. Prog. 1 auf Tuner 2) ein, so dass er beim nächsten Start definiert mit diesem Programm auf diesem Tuner "hochkommt". Der EPG-Scan erfolgt dann auf diesem Tuner und läuft - bei mir jedenfalls - problemlos durch. Tuner2Patch agiert ja im Vorfeld einer Aufnahme und kann daher beim SE-Scan nicht helfen - das schrieb FireBird auch schon mal so.
With StartConfig.tap does it set to tuner 2 when you power Toppy off from remote power button, or when scheduled recording ends and it automatically powers off? I mean does power off have to be done by StartConfig.tap or does it work background automatically?I've been using T2P with success (mostly) but nightly EPG scan cannot work with it since that is P-timer.

Benutzeravatar
wohliks
Elko-Papst
Elko-Papst
Beiträge: 4452
Registriert: Fr 9. Dez 2005, 15:36
Receivertyp: 2x VU+Duo4KSE; (no HD+)
Wohnort: Nordhessen

Re: Tuner2Patch TAP

#29

Beitrag von wohliks » Mo 17. Sep 2018, 15:07

2401 hat geschrieben:
Mo 17. Sep 2018, 15:03
With StartConfig.tap does it set to tuner 2 when you power Toppy off from remote power button, or when scheduled recording ends and it automatically powers off?
Interesting question - I don't now yet. Give me about a hour, I'll check this and report here.
Gruß Bernhard

2x VU+ Duo 4k SE - kein HD+ - SmartEPG
60 cm Astra (FTA only), hama LYPSI Quad LNB, Schwaiger SEW 4358 5/8-Multiswitch
FB: Logitech Harmony 650 & 600

Benutzeravatar
FireBird
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Beiträge: 28745
Registriert: Fr 9. Dez 2005, 09:59
Receivertyp: SRP-2401CI+ TFIR
vu+ Duo 4k
Wohnort: Wien

Re: Tuner2Patch TAP

#30

Beitrag von FireBird » Mo 17. Sep 2018, 15:10

2401 hat geschrieben:
Mo 17. Sep 2018, 14:52
he was talking about using some fluid too.
You need solder flux otherwise it will get worse.
and if I understood correctly he used a blow torch (flame?) and 2 minutes, that's pretty long.
I'm not sure too but if it really was a torch, he is lucky that his Toppy is working at all. Normally one need a heat gun or reflow workstation and not only heat the part but also the board around the part. Otherwise there will be even more mechanical stress.
Again this procedure is very ghetto way to try fix things and it can easily go wrong, so do not try it unless you are prepared to possibility that it can kill the unit.
Correct. This should be the last thing to try.
Best way would be to find company that has right equipment and knowledge to do this and it would be pretty permanently fixed.
If you have some time, you can watch Louis Rossmann how reballing really works and how to consume a lot of flux. :D

Benutzeravatar
FireBird
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Beiträge: 28745
Registriert: Fr 9. Dez 2005, 09:59
Receivertyp: SRP-2401CI+ TFIR
vu+ Duo 4k
Wohnort: Wien

Re: Tuner2Patch TAP

#31

Beitrag von FireBird » Mo 17. Sep 2018, 15:16

As Happy has added the source file for StartConfig, I could see that it reacts to the EVT_STOP event upon shutdown.

Benutzeravatar
wohliks
Elko-Papst
Elko-Papst
Beiträge: 4452
Registriert: Fr 9. Dez 2005, 15:36
Receivertyp: 2x VU+Duo4KSE; (no HD+)
Wohnort: Nordhessen

Re: Tuner2Patch TAP

#32

Beitrag von wohliks » Mo 17. Sep 2018, 15:21

FireBird hat geschrieben:
Mo 17. Sep 2018, 15:16
As Happy has added the source file for StartConfig, I could see that it reacts to the EVT_STOP event upon shutdown.
Ich muss es also nicht ausprobieren? Mein Gefühl sagt mir, es schaltet auch beim Shutdown nach einer Aufnahme um - aber ganz sicher bin ich nicht.
Gruß Bernhard

2x VU+ Duo 4k SE - kein HD+ - SmartEPG
60 cm Astra (FTA only), hama LYPSI Quad LNB, Schwaiger SEW 4358 5/8-Multiswitch
FB: Logitech Harmony 650 & 600

Benutzeravatar
FireBird
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Beiträge: 28745
Registriert: Fr 9. Dez 2005, 09:59
Receivertyp: SRP-2401CI+ TFIR
vu+ Duo 4k
Wohnort: Wien

Re: Tuner2Patch TAP

#33

Beitrag von FireBird » Mo 17. Sep 2018, 15:24

Brauchst Du nicht und laut Code passiert die Umschaltung bei jeder Art von Shutdown.

Benutzeravatar
wohliks
Elko-Papst
Elko-Papst
Beiträge: 4452
Registriert: Fr 9. Dez 2005, 15:36
Receivertyp: 2x VU+Duo4KSE; (no HD+)
Wohnort: Nordhessen

Re: Tuner2Patch TAP

#34

Beitrag von wohliks » Mo 17. Sep 2018, 15:25

FireBird hat geschrieben:
Mo 17. Sep 2018, 15:24
Brauchst Du nicht und laut Code passiert die Umschaltung bei jeder Art von Shutdown.
Danke - mein Gefühl trog mich also nicht...
Gruß Bernhard

2x VU+ Duo 4k SE - kein HD+ - SmartEPG
60 cm Astra (FTA only), hama LYPSI Quad LNB, Schwaiger SEW 4358 5/8-Multiswitch
FB: Logitech Harmony 650 & 600

2401
Topfazubi
Topfazubi
Beiträge: 49
Registriert: Do 6. Sep 2012, 16:58
Receivertyp: CRP-2401CI+
Receiverfirmware: 1.06.00

Re: Tuner2Patch TAP

#35

Beitrag von 2401 » Mo 17. Sep 2018, 15:43

wohliks hat geschrieben:
Mo 17. Sep 2018, 15:07
2401 hat geschrieben:
Mo 17. Sep 2018, 15:03
With StartConfig.tap does it set to tuner 2 when you power Toppy off from remote power button, or when scheduled recording ends and it automatically powers off?
Interesting question - I don't now yet. Give me about a hour, I'll check this and report here.
FireBird hat geschrieben:
Mo 17. Sep 2018, 15:16
As Happy has added the source file for StartConfig, I could see that it reacts to the EVT_STOP event upon shutdown.
FireBird hat geschrieben:
Mo 17. Sep 2018, 15:24
Brauchst Du nicht und laut Code passiert die Umschaltung bei jeder Art von Shutdown.
Thanks guys. So if I understood correctly EVT_STOP means it should work with every power off method, like remote power button (except of course pulling the plug :D)?


FireBird hat geschrieben:
Mo 17. Sep 2018, 15:10
You need solder flux otherwise it will get worse.
Yeah, I read about that fluxing when I repaired my PS3 but I was too lazy to get any but it worked that way too but not permanently, which I undestood was often also problem when it was done correctly with flux. Using heat gun is too off the specs reflow that it is pure luck if it gets fixed properly.
I'm not sure too but if it really was a torch, he is lucky that his Toppy is working at all. Normally one need a heat gun or reflow workstation and not only heat the part but also the board around the part. Otherwise there will be even more mechanical stress.
I think heat gun is better. I used one of those cheap heat guns with nozzle to better guide heat to small area.
Correct. This should be the last thing to try.
I probably will not try this if I get tap to work with warm up on all situations. It would be best to have it done at some professional shop that has suitable gear for that but they are pretty rare and not likely very cheap if you can find any. But obviously that would be pretty long term fix, probably last longer than some other part that will fail next.
If you have some time, you can watch Louis Rossmann how reballing really works and how to consume a lot of flux. :D
I watched similar videos when I learned reflowing my PS3. It looks so damn easy when professionals do it. :)

Benutzeravatar
Ricki
ToppiHolic
ToppiHolic
Beiträge: 5626
Registriert: Fr 9. Dez 2005, 23:06
Receivertyp: 2xSky Q
MagentaTV MR601
2xUltimo4K DVB-S2x FBC
Receiverfirmware: Alle aktuell
Wohnort: Wetter/Hessen
Kontaktdaten:

Re: Tuner2Patch TAP

#36

Beitrag von Ricki » Mo 17. Sep 2018, 20:00

danke Euch, ich werde mal StartConfig installieren und schauen.
Es ist schon etwas merkwürdig das jetzt gehäuft Meldungen zu dem Problem kommen. Geplante Obsoleszenz?
cu
Ricki


SmartEPGvu+ & SmartFilervu+ Wiki

SAT Anlage - Kathrein: CAS 75 mit UAS 584 LNB & EXR 1512 (Multischalter 5 auf 12), Astra 19.2°E

VU+ ULTIMO 4K DVB-S2x FBC+Samsung SSD870 QVO , 2 TB
VU+ ULTIMO 4K DVB-S2x FBC+Kingston SSDSUV400S, 480 GB
Skin: Vu_HD_1080P mit angepassten Skinparts - VTi 15.0.02
Plugins: smartEPGvu+ , Multi QuickButton, OpenWebif, AutocutVfd, GithubPluginUpdater, InfoBarTunerState, VTi Panel

Panasonic TX-55GZW1509; Sony UBP-X700, Apple TV 4K, Fire TV 4K, Harmony Elite, Denon AVR-X2300W, Synology 716+ (6TB)

Benutzeravatar
FireBird
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Beiträge: 28745
Registriert: Fr 9. Dez 2005, 09:59
Receivertyp: SRP-2401CI+ TFIR
vu+ Duo 4k
Wohnort: Wien

Re: Tuner2Patch TAP

#37

Beitrag von FireBird » Mo 17. Sep 2018, 20:13

Ricki hat geschrieben:
Mo 17. Sep 2018, 20:00
Es ist schon etwas merkwürdig das jetzt gehäuft Meldungen zu dem Problem kommen. Geplante Obsoleszenz?
Bei diesem (scheinbar thermischen) Fehler kann ich mir das nicht vorstellen. Andererseits interessant, dass sie sich in relativ kurzer Zeit häufen.

2401
Topfazubi
Topfazubi
Beiträge: 49
Registriert: Do 6. Sep 2012, 16:58
Receivertyp: CRP-2401CI+
Receiverfirmware: 1.06.00

Re: Tuner2Patch TAP

#38

Beitrag von 2401 » Mo 17. Sep 2018, 22:11

Ricki hat geschrieben:
Mo 17. Sep 2018, 20:00
danke Euch, ich werde mal StartConfig installieren und schauen.
Es ist schon etwas merkwürdig das jetzt gehäuft Meldungen zu dem Problem kommen. Geplante Obsoleszenz?
I believe EU regulations where they banned use of leaded solder in consumer electronics is the root cause. Especially in the beginning many manufacturers had problem with lead free solderings and I guess it is a little bit a feature of that solder that they will not last as well as leaded solderings.

Benutzeravatar
Ricki
ToppiHolic
ToppiHolic
Beiträge: 5626
Registriert: Fr 9. Dez 2005, 23:06
Receivertyp: 2xSky Q
MagentaTV MR601
2xUltimo4K DVB-S2x FBC
Receiverfirmware: Alle aktuell
Wohnort: Wetter/Hessen
Kontaktdaten:

Re: Tuner2Patch TAP

#39

Beitrag von Ricki » Do 20. Sep 2018, 17:53

Mit StartConfig läuft der EPG Scan jetzt sauber. T2Patch sorgt für ein vorhandenes Signal auf T1 beim aufnehmen.:thanks:
cu
Ricki


SmartEPGvu+ & SmartFilervu+ Wiki

SAT Anlage - Kathrein: CAS 75 mit UAS 584 LNB & EXR 1512 (Multischalter 5 auf 12), Astra 19.2°E

VU+ ULTIMO 4K DVB-S2x FBC+Samsung SSD870 QVO , 2 TB
VU+ ULTIMO 4K DVB-S2x FBC+Kingston SSDSUV400S, 480 GB
Skin: Vu_HD_1080P mit angepassten Skinparts - VTi 15.0.02
Plugins: smartEPGvu+ , Multi QuickButton, OpenWebif, AutocutVfd, GithubPluginUpdater, InfoBarTunerState, VTi Panel

Panasonic TX-55GZW1509; Sony UBP-X700, Apple TV 4K, Fire TV 4K, Harmony Elite, Denon AVR-X2300W, Synology 716+ (6TB)

Benutzeravatar
FireBird
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Suspekter verdächtiger Zauberküchenchef, TAP & Firmware-Guru
Beiträge: 28745
Registriert: Fr 9. Dez 2005, 09:59
Receivertyp: SRP-2401CI+ TFIR
vu+ Duo 4k
Wohnort: Wien

Re: Tuner2Patch TAP

#40

Beitrag von FireBird » Sa 22. Sep 2018, 11:05

Update auf V0.2, Erklärung im ersten Beitrag.

Antworten

Zurück zu „SRP/CRP TAP-Bereich“